Installing Linux to the EMMC using USB Serial Downloader

Understanding NXP uuu Tool

The i.MX 8M NAVQ Plus kit software manufacturing procedure makes use of the NXP uuu tool running on the Linux development host. The uuu tool performs installation of the Yocto images from the development host to the kit using the USB Serial Downloader interface.

The recommended Linux distributions to use on a development host are Ubuntu 20.04 and Fedora 35.

Locating uuu Tool and Scripts

A pre-built binary of the uuu tool can be found in the build directory:

If required, the recommended version of the uuu tool can be downloaded from the NXP github page: https://github.com/NXPmicro/mfgtools/releases/latest .

Installing Using USB Serial Downloader Protocol (SDP)

Perform the following step-wise procedure to install the Yocto images to the i.MX 8M NAVQ Plus kit:

Power the kit off by disconnecting the USB Type C cable from the development host.
Set the target boot mode to the USB serial downloader mode by setting the boot switches as follows:
- SW2.1 - 1
- SW2.2 - 0
Power the kit on by connecting the USB Type C cable to the development host. Use the kit port labeled USB1.

Check that the new USB device has appeared on your development host:

[psl@i7 ~]$ lsusb | grep -i nxp 
Bus 001 Device 025: ID 1fc9:0146 NXP Semiconductors

On the host, go to the Yocto images build directory:
```
[psl@i7 ~]$ cd ~/5-15-5-DESKTOP/builddir/tmp/deploy/images/imx8mpnavq 
[psl@i7 imx8mmnavq]$ ls -1
...
imx-boot-imx8mpnavq-sd.bin-flash_evk
imx-image-desktop-ros-imx8mpnavq.wic.bz2
uuu
...
```
- The images above are:
- imx-boot-imx8mpnavq-sd.bin-flash_evk - U-Boot-ATF-OPTEE boot image;
- imx-image-desktop-ros-imx8mpnavq.wic.bz2 - Ubuntu 20 root filesystem;
- uuu - pre-built image of the uuu utility;

Unpack the compressed image of the root filesystem:

[psl@i7 imx8mmnavq]$ bzip2 -d imx-image-desktop-ros-imx8mpnavq.wic.bz2
...

Launch the uuu tool with appropriate script as a parameter for installing the bootable Linux image:

[psl@i7 imx8mmnavq]$ sudo ./uuu -v -b emmc_all imx-boot-imx8mpnavq-sd.bin-flash_evk imx-image-desktop-ros-imx8mpnavq.wic
uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.3.82-0-g9c56e46

Wait for Known USB Device Appear...

The uuu tool will proceed to install the Production Yocto image to the storage device (EMMC) on the target board:

uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.3.74-2-g302da91 

Success 1 Failure 0
...
1:3 7/ 7 [Done ] FB: Done

When uuu has finished, the bootable Linux image has been installed to the on-module storage. Given proper setting of the boot switches, next power-on will boot the target board from the EMMC storage device.

Verifying New Installation

Perform the following step-wise procedure to verify boot of the newly installed Linux images from the on-module EMMC:

Power the kit off by disconnecting the USB Type C cable from the development host.
Select the appropriate boot mode by setting the boot switches as follows::
- SW2.1 - 0
- SW2.2 - 1
Power the kit on by connecting the USB Type C cable to the development host.

Verify that the following Linux boot-up messages appear on the serial console:

NOTICE:  BL31: v2.4(release): 
NOTICE:  BL31: Built : 05:49:10, Mar  2 2022


U-Boot 2021.04-lf_v2021.04+g60519b47e7 (Jul 31 2022 - 08:56:04 +0000)

CPU:   i.MX8MP[8] rev1.1 1800 MHz (running at 1200 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 44C
Reset cause: POR
Model: Voxelbotics NAVQ+ board
DRAM:  4 GiB
...
Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
...
Ubuntu 20.04.3 LTS imx8mpnavq ttymxc1

imx8mpnavq login:

Enter the Linux session by typing user for both the user name and password.