Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Table of Contents
minLevel1
maxLevel6
outlinefalse
stylenone
typelist
printablefalse

1. Understanding NXP uuu Tool

The i.MX 8M NAVQ Plus kit software manufacturing procedure makes use of the NXP uuu tool running on the Linux development host. The uuu tool performs installation of the Yocto images from the development host to the kit using the USB Serial Downloader interface.

The recommended Linux distributions to use on a development host are Ubuntu 20.04 and Fedora 35.

2. Locating uuu Tool and Scripts

A pre-built binary of the uuu tool can be found in the build directory:

If required, the recommended version of the uuu tool can be downloaded from the NXP github page: https://github.com/NXPmicro/mfgtools/releases/latest .

3. Installing Using USB Serial Downloader Protocol (SDP)

Perform the following step-wise procedure to install the Yocto images to the i.MX 8M NAVQ Plus kit:

  1. Power the kit off by disconnecting the USB Type C cable from the development host.

  2. Set the target boot mode to the USB serial downloader mode by setting the boot switches as follows:

    • SW2.1 - 1

    • SW2.2 - 0

  3. Power the kit on by connecting the USB Type C cable to the development host. Use the kit port labeled USB1.

  4. Check that the new USB device has appeared on your development host:

    Code Block
    [psl@i7 ~]$ lsusb | grep -i nxp 
    Bus 001 Device 025: ID 1fc9:0146 NXP Semiconductors
  5. On the host, go to the Yocto images build directory:

    Code Block
    [psl@i7 ~]$ cd ~/5-15-5-DESKTOP/builddir/tmp/deploy/images/imx8mpnavq 
    [psl@i7 imx8mmnavq]$ ls -1
    ...
    imx-boot-imx8mpnavq-sd.bin-flash_evk
    imx-image-desktop-ros-imx8mpnavq.wic.zst
    uuu
    ...
    • The images above are:

    • imx-boot-imx8mpnavq-sd.bin-flash_evk - U-Boot-ATF-OPTEE boot image;

    • imx-image-desktop-ros-imx8mpnavq.wic.zst - Ubuntu root filesystem;

    • uuu - pre-built image of the uuu utility;

  6. Unpack the compressed image of the root filesystem:

    Code Block
    [psl@i7 imx8mmnavq]$ zstd -d imx-image-desktop-ros-imx8mpnavq.wic.zst
    ...
  7. Launch the uuu tool with appropriate script as a parameter for installing the bootable Linux image:

    Code Block
    [psl@i7 imx8mmnavq]$ sudo ./uuu -v -b emmc_all imx-boot-imx8mpnavq-sd.bin-flash_evk imx-image-desktop-ros-imx8mpnavq.wic
    uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.3.82-0-g9c56e46
    
    Wait for Known USB Device Appear...
  8. The uuu tool will proceed to install the Production Yocto image to the storage device (EMMC) on the target board:

    Code Block
    uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.3.74-2-g302da91 
    
    Success 1 Failure 0
    ...
    1:3 7/ 7 [Done ] FB: Done
  9. When uuu has finished, the bootable Linux image has been installed to the on-module storage. Given proper setting of the boot switches, next power-on will boot the target board from the EMMC storage device.

4. Verifying New Installation

Perform the following step-wise procedure to verify boot of the newly installed Linux images from the on-module EMMC:

...